We use cookies to offer you a more personalized and smoother experience. By visiting this website, you agree to our use of cookies. If you prefer not to accept cookies or require more information, please visit our Privacy Policy.
Si votre questions porte sur un domaine particulier, vous pouvez choisir directement une catégorie ci-contre pour les réponses aux questions les plus fréquentes:
Résultats:
Question (Q&A-161|499):
Are there any limitations for M.2 sockets on Intel 500 series motherboards?(5/1/2021)
Answer:The availability of and speed supported by M.2 sockets on Intel 500 series motherboards may differ depending on which CPU is in use. (11th Generation or 10th Generation Intel Core processor)
For the specifications of each product, please refer to the tables below.
All of the M..2 sockets on the following models can be used in combination with 11th and 10th Generation CPUs.
Model
11th Generation
10th Generation
Z590 OC FormulaZ590 Taichi
M2_1: Gen4x4M2_2: Gen3x4+SATAM2_3: Gen3x4+SATA
M2_1: Gen3x4M2_2: Gen3x4+SATAM2_3: Gen3x4+SATA
Z590M Pro4
M2_1: Gen4x4+SATAM2_2: Gen3x4+SATA
M2_1: Gen3x4+SATAM2_2: Gen3x4+SATA
B560M Steel Legend
M2_1: Gen4x4M2_2: Gen3x4+SATA
M2_1: Gen3x4M2_2: Gen3x4+SATA
B560M-ITX/ac
M2_1: Gen4x4+SATA
M2_1: Gen3x4+SATA
H510M-HDV/M.2H510M/acH510M-ITX/ac
M2_1: Gen3x4+SATA
M2_1: Gen3x4+SATA
Some of the M.2 sockets on the following models can only be used in combination with an 11th Generation CPU.
※M.2 sockets may share lanes with PCIe slots or SATA ports. For detailed specifications, please refer to the product page.
Question (Q&A-116|390):
Je ne peux pas installer Windows 7 / 8 sur mon périphérique de stockage NVMe. Comment dois-je procéder ?(3/1/2015)
Answer:Microsoft Windows 7 et Windows 8 n'intègrent pas de pilote NVMe, veuillez installer Microsoft Windows 8.1 ou une version ultérieure sur le périphérique de stockage NVMe.
Question (Q&A-106|351):
Mes périphériques eSATA ne sont pas détectés par le contrôleur SATA3 ASMedia sur les plateformes Z87. Comment résoudre ce problème ?(9/1/2013)
Question (Q&A-102|339):
J'obtiens systématiquement un écran bleu (BSOD) lors de l'installation du pilote ASMedia SATA3. Comment installer ce pilote sous Windows 8 ?(2/1/2013)
Answer:Si vous avez connecté le disque dur qui contient votre système d'exploitation sur les ports SATA3_A0/ SATA3_A1, veuillez utiliser le pilote intégré à Windows 8.
Vous pouvez également connecter le disque dur sur les ports SATA3_0/ SATA3_1 et installer le pilote ASMedia SATA3 à nouveau.
Question (Q&A-101|333):
Pourquoi mes disques durs ne sont-ils pas détectés durant l'installation de WIndows XP ?(1/1/2013)
Answer:Il y a plusieurs causes possibles à ce problème, veuillez essayer les différentes suggestions ci-dessous :
1. Assurez vous que les câbles SATA et d'alimentation de vos HDDs sont correctement connectés à la carte mère.
2. Accédez à l'interface du BIOS, rendez vous dans la section Advanced / Storage Configuration puis réglez Sata Mode sur [IDE].
Si vous souhaitez installer Windows XP en mode [AHCI], vous devrez préinstaller le pilote adéquat. Reportez vous au lien ci-dessous pour plus d'informations: https://www.asrock.com/support/qa/TSDQA-45.pdf
3. Si vous avez essayé toutes les suggestions ci-dessus, changez de câbles SATA et de connecteurs sur la carte mère pour vérification.
Question (Q&A-101|331):
J'ai monté un volume RAID0 et je souhaite y installer un système d'exploitation. Quelle doit être la taille des secteurs pour pouvoir procéder à l'installation d'un OS ?(1/1/2013)
Answer:Pour Windows 7 et Windows 8, veuillez définir une taille de secteur de 512KB ou 1024KB.
Pour les systèmes Linux, vous pouvez définir une taille de secteur de 512KB, 1024KB, 2048KB ou 4096KB.
Question (Q&A-99|326):
Je veux pouvoir bénéficier de la fonction TRIM pour le mode RAID. Quel système est compatible avec la fonction TRIM en mode RAID 0 ?(11/1/2012)
Answer:Selon la documentation d'Intel, pour être compatible TRIM en mode RAID 0, un système doit remplir les conditions suivantes :
1. SSD compatible TRIM
2. Carte mère équipée d'un chipset Intel 7-Series
3. Windows 7 (Windows 8 sera compatible TRIM en mode RAID 0 prochainement)
4. Volume RAID 0
5. Technologie Intel Rapid Storage version 11.0 ou ultérieure
6. Intel SSD Toolbox version 3.1.1 ou ultérieure
Question (Q&A-95|314):
Lorsque je paramètre le SATA en mode RAID ou AHCI, je n'ai plus accès aux informations S.M.A.R.T avec des utilitaires comme AIAX64 ou CrystalDiskInfo, pourquoi ?(5/1/2012)
Answer:Veuillez utiliser Intel Rapid Storage pour contrôler les valeurs S.M.A.R.T en mode RAID ou AHCI. Les valeurs S.M.A.R.T sont présentées sous forme d'alertes dans l'interface utilisateur Intel Rapid Storage ou via l'icône dans la barre de tâches.
Pour plus d'informations, veuillez vous reporter au site officiel d'Intel : http://www.intel.com/support/chipsets/imsm/sb/cs-015002.htm
Question (Q&A-88|292):
Je voudrais utiliser le logiciel WD SmartWare pour une sauvegarde de mon système. Mais lorsque ASRock XFast USB est activé, WD SmartWare refuse de fonctionner. Que puis-je faire ?(9/1/2011)
Question (Q&A-86|289):
J'ai installé un système d'exploitation Microsoft® Windows® en mode GPT et Ubuntu en mode MBR sur deux disques durs différents, et je ne peux plus démarrer sur l'OS Microsoft® Windows®. Comment résoudre ce problème ?(6/1/2011)
Answer:Veuillez installer les deux systèmes d'exploitation en mode GPT ou en mode MBR.
Si vous installez les deux OS en mode GPT, veuillez vous référer aux indications suviantes :
1. Démarrez et accédez au BIOS puis rubrique [Boot]→[PCI ROM Priority]→ sélectionnez [EFI Compatible ROM], puis pressez la touche "F10" pour sauvegarder les changements et quittez le BIOS.
2. Au démarrage, pressez la touche "F11" et sélectionnez "UEFI:[Le nom de votre lecteur optique]" pour installer l' OS.
Si vous installez les deux OS en mode MBR, veuillez vous référer aux indications suivantes :
Au démarrage, pressez la touche "F11" et sélectionnez "AHCI/SATA:[Le nom de votre lecteur optique]" pour installer l' OS.
Question (Q&A-83|279):
Je voudrais installer Windows® 7 x64 sur un disque dur au format GPT, quelles sont les précautions à prendre avant l'installation ?(3/14/2011)
Answer:Nous vous conseillons d'installer le correctif pour Windows® 7 si vous souhaitez effectuer ce type d'installation.
Veuillez vous reporter au lien ci-dessous au sujet de ce correctif Microsoft® : http://support.microsoft.com/kb/979903
Question (Q&A-81|273):
Pourquoi la boite de dialogue MarvellTray.exe s'affiche t'elle à chaque démarrage sous Windows® 7 x64?(12/30/2010)
Answer:Celà est relatif au niveau de sécurité du contrôle de compte d'utilisateurs sous Windows® 7 x64.
Vous devez mettre à jour le pilote et l'utilitaire Marvell, cette boite de dialogue cessera alors de s'afficher à chaque lancement.
Veuillez suivre la procédure suivante pour mettre à jour le pilote et l'utilitaire Marvell :
1. Veuillez désinstaller le pilote Marvell et l'utilitaire RAID installés sur votre système.
2. Veuillez télécharger les pilotes et l'utilitaire les plus récents via le lien suivant.
Lien de téléchargement du pilote Marvell SATA3 driver ver:1.0.0.1051 : https://download.asrock.com/Drivers/All/SATA3/Marvell_SATA3_Win7-64(1.0.0.1051-WHQL).zip
Lien de téléchargement de l'utiliataire Marvell RAID Utility ver:4.1.0.1909 : https://download.asrock.com/Drivers/All/SATA3/Marvell_RAID_Win7-64(4.1.0.1909).zip
Question (Q&A-79|266):
J'utilise un disque dur Samsung HD323HJ / HD502HJ / HD503HI / HD103SJ / HD105SI sur une plateforme à base de chipset AMD® SB850, mais le disque ne démarre pas lorsque je lance mon système. Que puis-je faire ?(5/6/2010)
Answer:Veuillez vous rendre sur le site internet de Samsung pour obtenir une mise à jour du firmware de votre disque.
Vous pouvez également consulter la FAQ de Samsung pour plus d'informations depuis le lien ci-dessous : http://www.samsung.com/global/business/hdd/faqView.do?b2b_bbs_msg_id=308
Question (Q&A-79|265):
Mon système se bloque lorsque j'utilise un disque dur Western Digital Advanced Format sous Windows® XP. Que puis-je faire ?(5/6/2010)
Answer:Veuillez régler les jumpers sur 7-8 comme indiqué ci-dessous :
Question (Q&A-72|248):
Lorsque je branche un disque dur eSATA, le BIOS le reconnaît. Mais le système d'exploitation affiche le message « Périphérique de stockage déconnecté », et je ne peux pas utiliser ce disque dur eSATA. Que puis-je faire ?
(3/28/2009)
Answer:Veuillez suivre la procédure ci-dessous:
1.Veuillez lancer la console Intel® Matrix Storage et effectuer un clic droit sur le périphérique eSATA. Cliquez sur [Reset Hard Drive to Non-RAID].
2.Veuillez ensuite redémarrer votre ordinateur après avoir validé l'option [Reset Hard Drive to Non-RAID].
3.Dans le gestionnaire de disques, votre disque eSATA est désormais reconnu et vous pouvez créer un nouveau volume simple.
4.Le disque dur eSATA sera alors reconnu par le système.
Question (Q&A-70|244):
Lorsque je crée un volume RAID supérieur à 2.0 TB, ce volume RAID n'est pas reconnu après avoir installé le pilote RAID Durant l'installation de Windows® XP. Pourquoi ?(1/12/2009)
Answer:En raison des limitations relatives au système d'exploitation, Windows® XP ne supporte que le format MBR. Le format MBR ne reconnait pas les capacités supérieures à 2.0 TB.
Si vous souhaitez utiliser un volume RAID supérieur à 2.0 TB, les trios conditions ci-dessous doivent être remplies :
1.Votre système d'exploitation doit être Windows® Vista™ x64 SP1 ou Windows® 7 64bit.
2.Vous devez disposer d'un Bios EFI.
3.Vous devez utiliser le format GPT.
Veuillez vous reporter au lien ci-après pour plus d'informations.
Lien :
http://support.microsoft.com/?scid=kb;en-us;946557&x=9&y=7
http://www.microsoft.com/whdc/device/storage/GPT_FAQ.mspx
Question (Q&A-51|195):
J'utilise une carte mère ConRoeXFire-eSATA2/ 775XFire-eSATA2+/ 775XFire-eSATA2/ 775XFire-VSTA/ 775XFire-RAID. Mon système d'exploitation a été installé sur une disque dur SATA/SATA2 en mode "IDE". Lorsque j'installe le pilote SATA2 (Intel® Matrix Storage Manager), le système m'affiche le message d'erreur suivant : " Cet ordinateur ne propose pas la configuration minimale pour installer ce logiciel" (This computer does not meet the minimum requirements for installing this software). Pourquoi ?
Mode IDE (Dans le BIOS) :
Pilote SATA2 :
Message d'erreur :
(2/15/2007)
Answer:Le pilote SATA2 "Intel® Matrix Storage Manager" est prévu pour une utilisation en mode RAID ou AHCI. Si votre système d'exploitation a été installé en mode "IDE", vous n'avez pas besoin d'installer ce pilote.
Question (Q&A-47|185):
During the POST, there is a number "0075" or "0078" showed at the right corner of the screen, and the system stop for a long time. What can I do?(10/20/2006)
Answer:The problem may be caused by incorrect jumper settings or bad cables of your IDE or SATA devices. Please refer to following steps to check your system. For IDE devices:
1.If you connect 2 IDE devices to 1 IDE cable, please double check the jumpers of your IDE devices if they were set correctly. The device which is connected to the black connector should be set as master, and the other should be set as slave (gray connector).
2.Please exchange the devices of master and slave on the IDE cable.
3.Please replace the IDE cable by a new one.
4.Please replace the IDE hard drive by a new one.
For SATA devices:
1.Please adjust the jumpers of your SATA2 (3.0 Gb/s) hard disk drive as SATA1 (1.5 Gb/s) mode if your motherboard supports SATA1 (1.5 Gb/s) mode only.
2.Please replace the SATA cable by a new one.
3.Please replace the SATA hard drive by a new one.
Question (Q&A-44|177):
I'm using a SATA HDD. My computer was running fine. But one day I turn on my computer, it keeps restarting itself after Windows® Logo page (at startup). Do you have any idea what possibility causes this?(7/21/2006)
Answer:This may be that your system was installed in IDE (or non-RAID) mode. But now it is set to RAID (AHCI) Mode. Please try to set it back to the IDE (non-RAID) mode in the BIOS>Advanced>IDE Configuration.
Here are some examples, please refer to the user manual for details.
VIA® and Nvidia chipset:
Please set SATA Operation Mode to [non-RAID]
Intel® Chipset:
Please set Configure SATA as [IDE]
775Twins-HDTV (R2.0) or P4Twins-HDTV:
Please set ATA Combination Mode to [Enable]
Question (Q&A-33|145):
My SATA HD is WD 800JD. But the HDD cannot be detected by VIA 8237/8237R based motherboards. How do I solve it?(7/15/2005)
Answer:Please refer the following picture to install a jumper shunt on pins 5 and 6. It will enable HDD SATA 150MB/s only operation. Then the HDD will be detected by VIA SATA motherboards.
For further detail information, please refer WD Web Site.
http://wdc.custhelp.com/cgi-bin/wdc.cfg/php/enduser/std_adp.php?p_faqid=1337&p_created=1112379341&p_sid=8iB39lKh&p_lva=&p_sp=cF9zcmNoPTEmcF9zb3J0X2J5PSZwX2dyaWRzb3J0PSZwX3Jvd19jbnQ9MTAmcF9wcm9kcz05NSZwX2NhdHM9MTgzJnBfcHY9MS45NTsyLnUwJnBfY3Y9MS4xOD
http://wdc.custhelp.com/cgi-bin/wdc.cfg/php/enduser/std_adp.php?p_faqid=1228&p_created=1090517232&p_sid=vbCxCUJh&p_lva=&p_sp=cF9zcmNoPTEmcF9zb3J0X2J5PSZwX2dyaWRzb3J0PSZwX3Jvd19jbnQ9MiZwX3Byb2RzPSZwX2NhdHM9JnBfcHY9JnBfY3Y9JnBfc2VhcmNoX3R5cGU9c2Vhcm
Question (Q&A-32|141):
I would like to use a big capacity Hard Disk on ASRock motherboard. I wonder how large of capacity can ASRock motherboard support at most?(6/23/2005)
Answer:ASRock motherboards support 48-bit LBA mode hard drive. At present, ASRock motherboards have no limitation for the capacity of Hard Disk, so you can use over 127GB or 137GB Hard Disk on them.
If you want to get a full capacity under Windows XP/2000, please make sure that your operating system can support 48-bit LBA mode. Please refer to the following link:
https://www.asrock.com/support/QA/TSDQA-01.pdf
Question (Q&A-29|131):
When I use a Maxtor 250GB hard drive on my ASRock motherboards, the operating system Windows® 2000 or XP only recognizes 128 GB or 137GB. How should I fix this problem?(3/21/2005)
Answer:Please download "Maxtor Big Drive Enabler" from Maxtor website: http://www.seagate.com/ww/v/index.jsp?locale=en-US&name=Maxtor_Big_Drive_Enabler&vgnextoid=535d8b9c4a8ff010VgnVCM100000dd04090aRCRD to fix the problem.
Question (Q&A-27|122):
My hard drives are Maxtor Diamond MAX 10 and MaxLine III SATA 250 GB and 300 GB with 16 MB cache buffer. My hard drives can not be detected correctly during the POST, what can I do?(1/18/2005)
Answer:Please update to the newest BIOS of motherboard. If you still encounter problem, please contact Maxtor and update to the newest firmware of hard drives.
Question (Q&A-27|123):
If I use a SATA HDD and an IDE HDD together on P4i65GV, how do I boot from SATA HDD?(1/18/2005)
Answer:If you connect SATA HDD and IDE HDD together on P4i65GV, you will see an item of the BIOS setting- Hard Disk Drives (please refer to the following pictures).
Please entry the setting, choose your SATA drive as the "1st Drive" and then press "F10" to save the setting and exit.
Question (Q&A-20|100):
I have an Intel ICH5 chipset based motherboard. I found that my SATA hard drive is not recognized under Linux. What should I do?(6/11/2004)
Answer:Serial ATA (SATA) is a relatively new technology that was not previously available in Linux. To solve this problem, the Kernel of your Linux operating system needs to be updated. Please kindly refer to the following link for solution which is provided by Intel. http://www.intel.com/support/chipsets/sb/CS-006312.htm
Question (Q&A-20|99):
I have installed 1 SATA HDD and 1 IDE HDD (or SCSI card with SCSI HDD) on my P4i48 motherboard, how can I select IDE HDD (or SCSI HDD) in the Boot Device Priority?(6/11/2004)
Answer:If you would like to select IDE HDD in the Boot Device Priority menu, please set the IDE HDD to the first device of boot sequence in the Hard Disk Drives menu first.
AMI core 8 based BIOS would separate connected bootable devices into 3 groups, Hard Disk, Removable, and CD/DVD drives. Only first boot sequence of device in each group can be selected in the Boot Device Priority menu.
Question (Q&A-19|96):
My hard drive is 160 GB, when I install Windows 2000 or Windows XP, I can only see 137 GB. However, when I install this 160 GB hard drive on the ATA 133 RAID card, I can use whole 160 GB. What's wrong?(5/15/2004)
Answer:If you would like to use whole 160 GB as only one partition while installing the Windows OS, please make sure that your OS is Windows 2000 service pack 4 included or Windows XP service pack 1 included.
When you install the hard drive on the RAID card, you would need to press F6 to install third party driver during the Windows installation, and the driver is the reason why you can use whole 160 GB even your Windows XP service pack 1 is not included.
Question (Q&A-18|91):
I bought a new large size (80GB) HDD. After I installed it to my ASRock M/B, the BIOS only recognized it as a 32GB HDD. How can I get the full capacity of the HDD?(4/15/2004)
Answer:Please understand that most HDDs provide a jumper setting that will limit the maximum capacity, such as 32GB or 2GB. Please kindly double check the jumper setting of your HDD, and adjust the jumper setting to the correct position instead of the "Limit drive capacity" position.
Question (Q&A-14|77):
I want to use the hot plug feature with my SATA HDD. What requirements do I need to know?(12/12/2003)
Answer:Please read below operation guide of Serial ATA HDD Hot-Plug on ASRock motherboard carefully.
Before you process the SATA HDD Hot-Plug, please check below cable accessories from the motherboard gift box pack.
7-pin SATA data cable x 2
SATA power cable with SATA 15-pin power connector interface x 1
1.Without SATA 15-pin power connector interface, the Serial ATA HDD Hot-Plug cannot be processed.
2.Even some SATA HDDs provide both SATA 15pin power connector and IDE 1x4-pin conventional power connector interfaces, the IDE 1x4-pin conventional power connector interface is definitely not able to support Hot-Plug and will cause the HDD damage and data loss.
Points of Attention – Before you start to process the Hot-Plug:
Below operation procedure is designed only for ASRock motherboard, which supports SATA HDD Hot-Plug.
*SATA Hot-Plug support of ASRock motherboard is indicated in the product spec on our web site .
Make sure your SATA HDD can support hot-plug function from your dealer or HDD user manual. The SATA HDD, which cannot support hot-plug function, will be damaged under the hot-plug operation.
Please make sure the SATA driver is installed into system properly.
The latest SATA driver is available on our support web site https://www.asrock.com/support/index.asp
Make sure to use the SATA power cable & data cable, which are from ASRock motherboard package.
Please follow below instructions step by step to reduce the risk of HDD crash or data loss.
How to Hot-Plug a SATA HDD:
Points of Attention – Before you process the Hot-plug:
Please do follow below instruction sequence to process the Hot-plug, improper plug procedure will cause the SATA HDD damage and data loss.
How to Hot-Unplug a SATA HDD:
Points of Attention – Before you process the Hot-Unplug:
Please do follow below instruction sequence to process the Hot-unplug, improper unplug procedure will cause the SATA HDD damage and data loss.
Question (Q&A-13|67):
I'm using Intel chipset based motherboard. After installing Win98SE and all drivers, the data transfer rate from IDE devices (HDD or CDROM) seems not fast enough. Is there any thing I can do?(11/14/2003)
Answer:When installing Win98SE on Intel chipset based motherboard, please remember to enable the DMA mode to increase the IDE performance. To enable DMA mode in Win98SE, please go to "System"---"Device Manager"----"Disk Drives"----"Generic IDE Disk Type47" and manually check the "DMA" box in "Generic IDE Disk Type47".
Question (Q&A-1|1):
Why can't I boot up my system with one hard drive on primary IDE and an optical device (CD-ROM, DVD-ROM, CD-RW, etc...) on secondary IDE If connecting the hard drive/optical device as the secondary drive?(10/29/2002)
Answer:For best compatibility and stability, please make sure your stand alone hard drive on primary IDE has jumper setting to master, and your stand alone optical device on secondary IDE has jumper setting to master, too. Also if you only have one hard drive without any other optical device, please connect the hard drive to primary IDE with its jumper setting to master. Furthermore, for optimizing the transfer rate for the hard drive, we recommend you to connect your hard drive(s) to the primary IDE channel and optical device(s) to the secondary IDE channel.
Question (Q&A-1|5):
I have a drive that is larger than 137 GB but the operating system only recognizes 128 GB or 137 GB. How can I fix this?(10/29/2002)
Answer:First, The OS (for example Windows series) should be able to support 48-bit LBA mode that enables the system to run and manipulate big drive, namely, only Windows 2000 and Windows XP could achieve this goal.
Secondary, install Service Pack to let OS support large than 137GB HDD.
Windows XP, please download and installed the latest Service Pack 1, this can support big drive directly. For further information, please refer to Microsoft's Product Support Site:
http://support.microsoft.com/default.aspx?scid=kb;en-us;Q303013
Windows 2000, please download and installed the latest Service Pack 3. For further information, please refer to Microsoft's Product Support Site:
http://support.microsoft.com/default.aspx?scid=kb;en-us;Q305098