We use cookies to offer you a more personalized and smoother experience. By visiting this website, you agree to our use of cookies. If you prefer not to accept cookies or require more information, please visit our Privacy Policy.
Jeżeli wiesz do jakiej kategorii można zaliczyć twoje pytanie, możesz wybrać jedną z następujących kategorii:
Wyniki:
P (Q&A-161|499):
Are there any limitations for M.2 sockets on Intel 500 series motherboards?(5/1/2021)
O:The availability of and speed supported by M.2 sockets on Intel 500 series motherboards may differ depending on which CPU is in use. (11th Generation or 10th Generation Intel Core processor)
For the specifications of each product, please refer to the tables below.
All of the M..2 sockets on the following models can be used in combination with 11th and 10th Generation CPUs.
Model
11th Generation
10th Generation
Z590 OC FormulaZ590 Taichi
M2_1: Gen4x4M2_2: Gen3x4+SATAM2_3: Gen3x4+SATA
M2_1: Gen3x4M2_2: Gen3x4+SATAM2_3: Gen3x4+SATA
Z590M Pro4
M2_1: Gen4x4+SATAM2_2: Gen3x4+SATA
M2_1: Gen3x4+SATAM2_2: Gen3x4+SATA
B560M Steel Legend
M2_1: Gen4x4M2_2: Gen3x4+SATA
M2_1: Gen3x4M2_2: Gen3x4+SATA
B560M-ITX/ac
M2_1: Gen4x4+SATA
M2_1: Gen3x4+SATA
H510M-HDV/M.2H510M/acH510M-ITX/ac
M2_1: Gen3x4+SATA
M2_1: Gen3x4+SATA
Some of the M.2 sockets on the following models can only be used in combination with an 11th Generation CPU.
※M.2 sockets may share lanes with PCIe slots or SATA ports. For detailed specifications, please refer to the product page.
P (Q&A-116|390):
Nie mogę zainstalować systemu Windows 7, 8 na moim urządzeniu zgodnym z NVMe. Co powinienem zrobić?(3/1/2015)
O:Microsoft Windows 7 i Windows 8 nie działają ze sterownikiem NVMe, należy zainstalować system Microsoft Windows 8.1 lub nowszy na urządzeniu zgodnym z NVMe.
P (Q&A-106|351):
Moje urządzenie z interfejsem eSATA nie może być wykryte przez kontroler ASMedia SATA3 na płycie głównej z chipsetem Z87. Jak powinienem rozwiązać ten problem?(9/1/2013)
P (Q&A-102|339):
Przy instalacji sterownika ASMedia SATA3 cały czas pojawia się BSOD. Jak mogę zainstalować sterownik ASMedia SATA3 na Windows 8?(2/1/2013)
O:Jeśli podłączasz dysk twardy zawierający system operacyjny do jednego z portów SATA3_A0 / SATA3_A1, użyj zintegrowanych sterowników Windows 8.
Inną możliwością jest podłączenie dysku HDD do portów SATA3_0/ SATA3_1 i ponowna instalacja sterowników ASMedia SATA3.
P (Q&A-101|333):
Dlaczego system nie wykrywa dysków HDD, kiedy chcę zainstalować system Windows XP?(1/1/2013)
O:Istnieją różne przyczyny tego problemu, należy odnieść się do następujących wskazówek w celu sprawdzenia systemu.
1. Prosimy upewnić się, że kabel zasilania i kabel SATA są połączone z dyskiem i płytą główną.
2. Przejdź do ekranu konfiguracji BIOS, wejdź w zakładkę Storage Configuration i ustaw tryb SATA na [IDE].
Jeśli chcesz zainstalować system Windows XP w trybie [AHCI], ze względu na wymagania systemu Windows XP, musisz wcześniej zainstalować sterownik SATA. Zapoznaj się z poniższym FAQ dla poznania dalszych kroków.
Link: https://www.asrock.com/support/qa/TSDQA-45.pdf
3. Jeśli powyższe testy zostały już przeprowadzone, proszę zmienić kabel SATA lub port SATA w celu weryfikacji.
P (Q&A-101|331):
Zbudowałem wolumin RAID 0 i chcę zainstalować system operacyjny na tym woluminie RAID. Jak duży rozmiar sektora powinienem ustawić, aby móc zainstalować system operacyjny?(1/1/2013)
O:W systemie Windows 7 i Windows 8, należy zainstalować system operacyjny z rozmiarem sektora 512KB lub 1024KB.
Dla systemów Linux, należy zainstalować system operacyjny z rozmiarem sektora 512KB, 1024KB, 2048KB lub 4096KB.
P (Q&A-99|326):
Chcę korzystać z funkcji TRIM dla macierzy RAID. Jaki system zapewnia wsparcie TRIM dla RAID 0?(11/1/2012)
O:Według dokumentów Intela, system wspierający TRIM dla RAID 0 musi spełniać następujące warunki.
1. Proszę sprawdzić, czy SSD obsługuje funkcję TRIM.
2. Płyta główna bazująca na chipsecie Intel 7-Series.
3. Windows 7 (Windows 8 będzie wspierać TRIM dla RAID 0 w przyszłości)
4. RAID 0 dla dysków SSD.
5. Oprogramowanie Intel Rapid Storage Technology 11.0 lub nowszej wersji.
6. Intel SSD Toolbox 3.1.1 lub nowszej wersji.
P (Q&A-95|314):
Dlaczego nie widzę wartości S.M.A.R.T w narzędziach takich jak AIAX64 czy CrystalDiskInfo, kiedy dysk SATA ustawiony jest w trybie RAID lub AHCI?(5/1/2012)
O:Wartości S.M.A.R.T. dysków pokazywane są w panelu oprogramowania Intel Rapid Storage Technology dostępnego m.in. z obszaru powiadomień paska zadań.
P (Q&A-88|292):
Chciałbym używać oprogramowania WD SmartWare do robienia kopii zapasowych systemu, ale w przypadku, gdy mam uaktywnioną funkcję ASRock XFast USB, oprogramowanie WD SmartWare nie działa. Co powinienem zrobić?(9/1/2011)
P (Q&A-86|289):
Instaluję system Microsoft® Windows® w trybie GPT oraz system Ubuntu w trybie MBR na dwóch różnych dyskach HDD, ale nie mogę uruchomić system Microsoft® Windows®. Jak rozwiązać ten problem?(6/1/2011)
O:Proszę zainstalować obydwa systemy w trybie GPT lub MBR.
Obydwa systemy w trybie GPT:
1. Wejdź do BIOS-u -> [Boot] -> [PCI ROM Priority] -> wybierz [EFI Compatible ROM], następnie wciśnij klawisz "F10" by zapisać zmiany i wyjść.
2. Następnie wciśnij klawisz „F11" podczas bootowania i wybierz „UEFI:[your ODD name]" w celu zainstalowania systemu operacyjnego.
Obydwa systemy w trybie MBR:
Wciśnij klawisz "F11" podczas bootowania i wybierz opcję "AHCI/SATA:[your ODD name]" w celu zainstalowania systemu operacyjnego.
P (Q&A-83|279):
Chciałbym zainstalować system Windows 7 x64 na dysku z tablicami typu GPT. Co powinienem zrobić wcześniej?(3/14/2011)
P (Q&A-79|266):
Podłączyłem dysk twardy Samsung HD323HJ / HD502HJ / HD503HI / HD103SJ / HD105SI HDD do płyty głównej z chipsetem AMD SB850, ale kiedy chcę uruchomić system, dysk nie może wystartować. Co powinienem zrobić?(5/6/2010)
P (Q&A-79|265):
Kiedy próbuję, w systemie Windows XP, sformatować dysk programem WD Advanced Format, komputer się zawiesza. Jak mogę to naprawić?(5/6/2010)
O:Załóż zworkę na piny 7-8 dysku twardego, tak jak na poniższym rysunku:
P (Q&A-72|248):
Kiedy podłączę dysk twardy eSATA, jest on rozpoznawany w BIOS-ie. W systemie operacyjnym widoczny jest tylko komunikat "Storage Device Connected" i nie mogę z niego korzystać. Jak mogę to naprawić?
(3/28/2009)
O:Proszę wykonać poniższe kroki.
1.Zainstaluj Intel® Matrix Storage Console i kliknij prawym przyciskiem myszy na eSATA hard device, a następnie [Reset Hard Drive to Non-RAID].
2.Po kliknięciu [Reset Hard Drive to Non-RAID] zrestartuj komputer.
3.Przejdź do zarządzania dyskami, twój dysk eSATA powinien być widoczny. Utwórz na nim nową partycję podstawową.
4.Twój dysk eSATA powinien być już widoczny.
P (Q&A-70|244):
Kiedy utworzę wolumen RAID o pojemności ponad 2 TB, nie jest on rozpoznawany po instalacji sterowników RAID w czasie instalacji Windows XP. Dlaczego?(1/12/2009)
O:Jest to spowodowane ograniczeniami systemu operacyjnego. Windows XP wspiera tylko format dysku MBR, który nie ma wsparcia dla dysków o pojemności ponad 2 TB.
Jeżeli chcesz używać wolumenu RAID większego niż 2 TB jako głównego dysku muszą być spełnione poniższe warunki:
1. Twój system operacyjny to Windows Vista x64 SP1 lub Windows 7 64bit.
2. EFI BIOS.
3. Format dysku GPT.
Sprawdź poniższe linki aby uzyskać więcej informacji.
P (Q&A-51|195):
I am using the ConRoeXFire-eSATA2/ 775XFire-eSATA2+/ 775XFire-eSATA2/ 775XFire-VSTA/ 775XFire-RAID motherboard. My Operating system was installed in a SATA/ SATA2 HDD with "IDE" mode. When I install the SATA2 driver (Intel® Matrix Storage Manager), system always pops an error message "This computer does not meet the minimum requirements for installing this software". Why?
IDE mode (In BIOS setup):
SATA2 driver:
Error Message:
(2/15/2007)
O:The Intel® Matrix Storage Manager (SATA2 driver) is for RAID or AHCI mode. If your operating system was built by "IDE" mode, you don't need to install it.
P (Q&A-47|185):
During the POST, there is a number "0075" or "0078" showed at the right corner of the screen, and the system stop for a long time. What can I do?(10/20/2006)
O:The problem may be caused by incorrect jumper settings or bad cables of your IDE or SATA devices. Please refer to following steps to check your system. For IDE devices:
1.If you connect 2 IDE devices to 1 IDE cable, please double check the jumpers of your IDE devices if they were set correctly. The device which is connected to the black connector should be set as master, and the other should be set as slave (gray connector).
2.Please exchange the devices of master and slave on the IDE cable.
3.Please replace the IDE cable by a new one.
4.Please replace the IDE hard drive by a new one.
For SATA devices:
1.Please adjust the jumpers of your SATA2 (3.0 Gb/s) hard disk drive as SATA1 (1.5 Gb/s) mode if your motherboard supports SATA1 (1.5 Gb/s) mode only.
2.Please replace the SATA cable by a new one.
3.Please replace the SATA hard drive by a new one.
P (Q&A-44|177):
I'm using a SATA HDD. My computer was running fine. But one day I turn on my computer, it keeps restarting itself after Windows® Logo page (at startup). Do you have any idea what possibility causes this?(7/21/2006)
O:This may be that your system was installed in IDE (or non-RAID) mode. But now it is set to RAID (AHCI) Mode. Please try to set it back to the IDE (non-RAID) mode in the BIOS>Advanced>IDE Configuration.
Here are some examples, please refer to the user manual for details.
VIA® and Nvidia chipset:
Please set SATA Operation Mode to [non-RAID]
Intel® Chipset:
Please set Configure SATA as [IDE]
775Twins-HDTV (R2.0) or P4Twins-HDTV:
Please set ATA Combination Mode to [Enable]
P (Q&A-33|145):
My SATA HD is WD 800JD. But the HDD cannot be detected by VIA 8237/8237R based motherboards. How do I solve it?(7/15/2005)
O:Please refer the following picture to install a jumper shunt on pins 5 and 6. It will enable HDD SATA 150MB/s only operation. Then the HDD will be detected by VIA SATA motherboards.
For further detail information, please refer WD Web Site.
http://wdc.custhelp.com/cgi-bin/wdc.cfg/php/enduser/std_adp.php?p_faqid=1337&p_created=1112379341&p_sid=8iB39lKh&p_lva=&p_sp=cF9zcmNoPTEmcF9zb3J0X2J5PSZwX2dyaWRzb3J0PSZwX3Jvd19jbnQ9MTAmcF9wcm9kcz05NSZwX2NhdHM9MTgzJnBfcHY9MS45NTsyLnUwJnBfY3Y9MS4xOD
http://wdc.custhelp.com/cgi-bin/wdc.cfg/php/enduser/std_adp.php?p_faqid=1228&p_created=1090517232&p_sid=vbCxCUJh&p_lva=&p_sp=cF9zcmNoPTEmcF9zb3J0X2J5PSZwX2dyaWRzb3J0PSZwX3Jvd19jbnQ9MiZwX3Byb2RzPSZwX2NhdHM9JnBfcHY9JnBfY3Y9JnBfc2VhcmNoX3R5cGU9c2Vhcm
P (Q&A-32|141):
I would like to use a big capacity Hard Disk on ASRock motherboard. I wonder how large of capacity can ASRock motherboard support at most?(6/23/2005)
O:ASRock motherboards support 48-bit LBA mode hard drive. At present, ASRock motherboards have no limitation for the capacity of Hard Disk, so you can use over 127GB or 137GB Hard Disk on them.
If you want to get a full capacity under Windows XP/2000, please make sure that your operating system can support 48-bit LBA mode. Please refer to the following link:
https://www.asrock.com/support/QA/TSDQA-01.pdf
P (Q&A-29|131):
When I use a Maxtor 250GB hard drive on my ASRock motherboards, the operating system Windows® 2000 or XP only recognizes 128 GB or 137GB. How should I fix this problem?(3/21/2005)
O:Please download "Maxtor Big Drive Enabler" from Maxtor website: http://www.seagate.com/ww/v/index.jsp?locale=en-US&name=Maxtor_Big_Drive_Enabler&vgnextoid=535d8b9c4a8ff010VgnVCM100000dd04090aRCRD to fix the problem.
P (Q&A-27|122):
My hard drives are Maxtor Diamond MAX 10 and MaxLine III SATA 250 GB and 300 GB with 16 MB cache buffer. My hard drives can not be detected correctly during the POST, what can I do?(1/18/2005)
O:Please update to the newest BIOS of motherboard. If you still encounter problem, please contact Maxtor and update to the newest firmware of hard drives.
P (Q&A-27|123):
If I use a SATA HDD and an IDE HDD together on P4i65GV, how do I boot from SATA HDD?(1/18/2005)
O:If you connect SATA HDD and IDE HDD together on P4i65GV, you will see an item of the BIOS setting- Hard Disk Drives (please refer to the following pictures).
Please entry the setting, choose your SATA drive as the "1st Drive" and then press "F10" to save the setting and exit.
P (Q&A-20|100):
I have an Intel ICH5 chipset based motherboard. I found that my SATA hard drive is not recognized under Linux. What should I do?(6/11/2004)
O:Serial ATA (SATA) is a relatively new technology that was not previously available in Linux. To solve this problem, the Kernel of your Linux operating system needs to be updated. Please kindly refer to the following link for solution which is provided by Intel. http://www.intel.com/support/chipsets/sb/CS-006312.htm
P (Q&A-20|99):
I have installed 1 SATA HDD and 1 IDE HDD (or SCSI card with SCSI HDD) on my P4i48 motherboard, how can I select IDE HDD (or SCSI HDD) in the Boot Device Priority?(6/11/2004)
O:If you would like to select IDE HDD in the Boot Device Priority menu, please set the IDE HDD to the first device of boot sequence in the Hard Disk Drives menu first.
AMI core 8 based BIOS would separate connected bootable devices into 3 groups, Hard Disk, Removable, and CD/DVD drives. Only first boot sequence of device in each group can be selected in the Boot Device Priority menu.
P (Q&A-19|96):
My hard drive is 160 GB, when I install Windows 2000 or Windows XP, I can only see 137 GB. However, when I install this 160 GB hard drive on the ATA 133 RAID card, I can use whole 160 GB. What's wrong?(5/15/2004)
O:If you would like to use whole 160 GB as only one partition while installing the Windows OS, please make sure that your OS is Windows 2000 service pack 4 included or Windows XP service pack 1 included.
When you install the hard drive on the RAID card, you would need to press F6 to install third party driver during the Windows installation, and the driver is the reason why you can use whole 160 GB even your Windows XP service pack 1 is not included.
P (Q&A-18|91):
I bought a new large size (80GB) HDD. After I installed it to my ASRock M/B, the BIOS only recognized it as a 32GB HDD. How can I get the full capacity of the HDD?(4/15/2004)
O:Please understand that most HDDs provide a jumper setting that will limit the maximum capacity, such as 32GB or 2GB. Please kindly double check the jumper setting of your HDD, and adjust the jumper setting to the correct position instead of the "Limit drive capacity" position.
P (Q&A-14|77):
I want to use the hot plug feature with my SATA HDD. What requirements do I need to know?(12/12/2003)
O:Please read below operation guide of Serial ATA HDD Hot-Plug on ASRock motherboard carefully.
Before you process the SATA HDD Hot-Plug, please check below cable accessories from the motherboard gift box pack.
7-pin SATA data cable x 2
SATA power cable with SATA 15-pin power connector interface x 1
1.Without SATA 15-pin power connector interface, the Serial ATA HDD Hot-Plug cannot be processed.
2.Even some SATA HDDs provide both SATA 15pin power connector and IDE 1x4-pin conventional power connector interfaces, the IDE 1x4-pin conventional power connector interface is definitely not able to support Hot-Plug and will cause the HDD damage and data loss.
Points of Attention – Before you start to process the Hot-Plug:
Below operation procedure is designed only for ASRock motherboard, which supports SATA HDD Hot-Plug.
*SATA Hot-Plug support of ASRock motherboard is indicated in the product spec on our web site .
Make sure your SATA HDD can support hot-plug function from your dealer or HDD user manual. The SATA HDD, which cannot support hot-plug function, will be damaged under the hot-plug operation.
Please make sure the SATA driver is installed into system properly.
The latest SATA driver is available on our support web site https://www.asrock.com/support/index.asp
Make sure to use the SATA power cable & data cable, which are from ASRock motherboard package.
Please follow below instructions step by step to reduce the risk of HDD crash or data loss.
How to Hot-Plug a SATA HDD:
Points of Attention – Before you process the Hot-plug:
Please do follow below instruction sequence to process the Hot-plug, improper plug procedure will cause the SATA HDD damage and data loss.
How to Hot-Unplug a SATA HDD:
Points of Attention – Before you process the Hot-Unplug:
Please do follow below instruction sequence to process the Hot-unplug, improper unplug procedure will cause the SATA HDD damage and data loss.
P (Q&A-13|67):
I'm using Intel chipset based motherboard. After installing Win98SE and all drivers, the data transfer rate from IDE devices (HDD or CDROM) seems not fast enough. Is there any thing I can do?(11/14/2003)
O:When installing Win98SE on Intel chipset based motherboard, please remember to enable the DMA mode to increase the IDE performance. To enable DMA mode in Win98SE, please go to "System"---"Device Manager"----"Disk Drives"----"Generic IDE Disk Type47" and manually check the "DMA" box in "Generic IDE Disk Type47".
P (Q&A-1|1):
Why can't I boot up my system with one hard drive on primary IDE and an optical device (CD-ROM, DVD-ROM, CD-RW, etc...) on secondary IDE If connecting the hard drive/optical device as the secondary drive?(10/29/2002)
O:For best compatibility and stability, please make sure your stand alone hard drive on primary IDE has jumper setting to master, and your stand alone optical device on secondary IDE has jumper setting to master, too. Also if you only have one hard drive without any other optical device, please connect the hard drive to primary IDE with its jumper setting to master. Furthermore, for optimizing the transfer rate for the hard drive, we recommend you to connect your hard drive(s) to the primary IDE channel and optical device(s) to the secondary IDE channel.
P (Q&A-1|5):
I have a drive that is larger than 137 GB but the operating system only recognizes 128 GB or 137 GB. How can I fix this?(10/29/2002)
O:First, The OS (for example Windows series) should be able to support 48-bit LBA mode that enables the system to run and manipulate big drive, namely, only Windows 2000 and Windows XP could achieve this goal.
Secondary, install Service Pack to let OS support large than 137GB HDD.
Windows XP, please download and installed the latest Service Pack 1, this can support big drive directly. For further information, please refer to Microsoft's Product Support Site:
http://support.microsoft.com/default.aspx?scid=kb;en-us;Q303013
Windows 2000, please download and installed the latest Service Pack 3. For further information, please refer to Microsoft's Product Support Site:
http://support.microsoft.com/default.aspx?scid=kb;en-us;Q305098