We use cookies to offer you a more personalized and smoother experience. By visiting this website, you agree to our use of cookies. If you prefer not to accept cookies or require more information, please visit our Privacy Policy.
Jeżeli wiesz do jakiej kategorii można zaliczyć twoje pytanie, możesz wybrać jedną z następujących kategorii:
Wyniki:
P (Q&A-152|488):
Posiadam płytę TRX40. W menedżerze urządzeń widoczne jest urządzenie RTK Boot z wykrzyknikiem, a port audio nie daje dźwięku. Jak to naprawić?(4/1/2020)
O:Jeśli urządzenie RTK pojawia się w menedżerze urządzeń i port audio jest nieczynny, wykonaj następujące kroki, aby usunąć urządzenie RTK i przywrócić sprawność portu audio.
Krok 5. Dwukrotnie kliknij na UacCodecDownload_AllInOne_RsProxy_2.64.10
Krok 6. Naciśnij guzik Start, aby rozpocząć flashowanie firmware'u audio.
Krok 7. Po zakończeniu procesu flashowania, narzędzie pokaże status Pass oznaczający prawidłowe zflashowanie firmware'u audio. Urządzenie RTK boot powinno nie być widoczne w menedżerze urządzeń.
P (Q&A-151|487):
Jeśli słyszysz syczące dźwięki w nagraniach, skorzystaj z jednej z poniższych metod, aby rozwiązać ten problem.(1/1/2020)
O:Jeśli słyszysz syczące dźwięki w nagraniach, skorzystaj z jednej z poniższych metod, aby rozwiązać ten problem.
Metoda 1:
Krok 1.
Pobierz sterownik Realtek high definition audio driver z strony ASRock.
*Upewnij się, że Twój kabel LAN jest podłączony podczas instalacji sterownika Realtek audio driver.
Metoda 2:
Krok 1.
Wykonaj kroki 1 i 2 metody 1, aby uruchomić konsolę "Realtek audio console”.
Krok 2.
Ustaw Microphone Boost (Wzmocnienie Mikrofonu) na +0db.
Krok 3.
Po ustawieniu wzmocnienia na +0db, jakość nagrań ulegnie poprawie.
P (Q&A-142|468):
W jaki sposób zainstalować Sound Blaster Connect APP w systemie Windows 10 RS4, lub jego późniejszej wersji?(10/1/2018)
O:W większości przypadków, system automatycznie pobierze aplikację w tle po zainstalowaniu sterownika Realtek Audio. Wpisz frazę "Sound Blaster Connect” w wyszukiwarce Win10, aby otworzyć program.
Jeżeli aplikacja nie pojawia się w Twoim systemie, wykonaj następujące kroki, aby zainstalować ją ręcznie.
1. Upewnij się, że Twoja płyta główna wspiera Creative Sound i posiadasz zainstalowany sterownik Realtek Audio.
* Odwiedź stronę specyfikacji płyty głównej www.ASRock.com
* Sterownik Realtek Audio może być zainstalowany z płyty wsparcia CD lub pobrany z oficjalnej strony ASRock.
2. Przejdź do strony "Sound Blaster Connect” w sklepie Microsoft Store i kliknij przycisk „Get”, aby rozpocząć pobieranie. https://www.microsoft.com/en-sg/store/p/sound-blaster-connect/9n66rljrt8z2
3. Po instalacji, naciśnij przycisk „Launch”, aby uruchomić aplikację.
W poniższej tabeli znajdziesz informacje, które płyty obsługują Creative SoundBlaster Cinema5.
P (Q&A-142|469):
Jak zainstalować aplikację Realtek Audio Console pod systemem Windows 10 RS4 lub jego późniejszej wersji?(10/1/2018)
O:W większości przypadków, system automatycznie pobierze aplikację w tle po zainstalowaniu sterownika Realtek Audio. Wpisz frazę "Realtek Audio Console” w wyszukiwarce Win10, aby otworzyć program.
* Podłącz przewód LAN podczas instalacji sterownika Realtek Audio.
Jeżeli aplikacja nie pojawia się w Twoim systemie, wykonaj następujące kroki, aby zainstalować ją ręcznie.
1. Przejdź do Menedżera Urządzeń, aby sprawdzić, czy sterownik Realtek Audio jest zainstalowany.
* Sterownik Realtek Audio może być zainstalowany z płyty wsparcia CD lub pobrany z oficjalnej strony www.ASRock.com.
2. Jeżeli zainstalowana jest zewnętrzna karta graficzna, włącz w BIOSie opcję "IGPU Multi-Monitor”.
Ścieżka BIOS: Advanced > Chipset Configuration > IGPU Multi-Monitor
3. Pobierz sterownik VGA wersja 15.60.01.4877 z centrum pobierania Intel i zainstaluj go na swoim komputerze.
Link pobierania: https://downloadcenter.intel.com/product/128199/Graphics-for-8th-Generation-Intel-Processors
4. Podłącz konektor USB 3.0 "Windows Mixed Reality Headset” do zintegrowanego portu USB3.0.
5. Podłącz konektor HDMI "Windows Mixed Reality Headset” do zintegrowanego portu HDMI.
Windows Mixed Reality Headset powinien już działać.
P (Q&A-135|455):
W jaki sposób odtwarzać Dolby ATMOS poprzez odbiornik na płycie Z270 Gaming-ITX/ac? (10/1/2017)
O:Prosimy o zapoznanie się z poniższymi wymaganiami, konfiguracją oraz procedurą instalacji.
[Wymagania]
System Operacyjny: Windows 10
Odbiornik/ dekoder: Onkyo TX-NR 747 lub inne odbiorniki wspierające HDCP 2.2
Odtwarzacz: Pioneer Ultra HD Blu-ray drive
Dysk BD: Dysk z filmem 3D / 4K BD
Oprogramowania Odtwarzające: Power DVD 14 lub późniejsza wersja
[Konfiguracja]
Płyta Główna: Z270 Gaming-ITX/ac
BIOS: P2.30
[Instalacja]
1. Podczas uruchamiania się komputera wciśnij "F2”, aby wejść do UEFI.
Przejdź do Advanced > CPU Configuration i włącz (Enable) "Software Guard Extensions" w ustawieniach BIOS.
Wciśnij "F10", aby zapisać zmiany i wyjść z BIOS.
2. Uruchom system operacyjny komputera i zainstaluj wszystkie sterowniki do płyty głównej.
Zainstaluj sterownik ME driver ver: 11.6.0.1126 (wsparcie dla Ultra HD Blu-ray). Pobierz sterownik z poniższego linku: http://www.asrock.com/MB/Intel/Fatal1ty%20Z270%20Gaming-ITXac/index.asp#osW1064
3. Przejdź do Panelu Sterownia > Sprzęt i Dźwięk > Dźwięk i wybierz "Wyjście odbiornika”.
P (Q&A-119|396):
Czy dźwięk DTS Connect 5.1 Surround działa w systemie Windows 10?(8/1/2015)
O:Ze względu na ograniczenia systemu Microsoft Windows 10, funkcja DTS Connect 5.1 Surround nie jest obsługiwana. Proszę wybrać wcześniejsze dystrybucje jak Windows 8, 8.1 lub 7.
P (Q&A-106|350):
Kiedy odtwarzam muzykę lub filmy przez Media Player w systemie Windows 8 32/64 bit, program niespodziewanie zatrzymuje się i wyświetla wiadomość o błędzie za każdym razem, gdy podłączam słuchawki do frontowego panelu. Co powinienem zrobić?(9/1/2013)
O:Proszę jeszcze raz otworzyć program Media Player oraz uruchomić plik ponownie, by ścieżka dźwiękowa była odtwarzana przez urządzenie podłączone do frontowego panelu audio.
P (Q&A-89|297):
Jak skonfigurować dźwięk (DTS 5.1, Dolby 5.1, DTS HD Master i Dolby True HD) poprzez złącze HDMI lub SPDIF?(11/1/2011)
O:Wymagania:
System operacyjny Windows 7, Vista SP2 lub późniejsze.
Odbiornik/dekoder: np. Wzmacniacz Onkyo TX-SR608:
Oprogramowanie: np. PowerDVD 10 v10.0.2025.52 lub inne.
Instalacja:
1.Proszę zainstalować wszystkie sterowniki z płyty CD/DVD oraz sprawdzić, czy w menadżerze urządzeń nie ma żadnych błędów (znaczki "!" lub "?").
2.Wejdź w Panel Sterowania -> Dźwięk
Jeżeli chcesz korzystać z dźwięku poprzez gniazdo HDMI, wybierz HDMI.
Jeżeli chcesz korzystać z dźwięku poprzez gniazdo SPDIF, wybierz Wyjście optyczne.
*Różne płyty główne/chipsety mogą różnić się oznaczeniami widocznymi powyżej.
3. Wejdź w ustawienia dźwięku w używanej aplikacji.
W oprogramowaniu Power DVD 10 wygląda to tak, jak na obrazku poniżej.
4.Wybierz dekoder/amplituner dla cyfrowego wyjścia audio.
5.Wybierz odpowiedni format zawartości/źródła.
6.Możesz odtwarzać materiał audio/wideo.
P (Q&A-78|263):
Używam panelu frontowego audio AC'97 z kartą dźwiękową VIA zintegrowaną na płycie głównej. Jak mogę podłączyć ten panel do złącza HD Audio na płycie?(2/10/2010)
O:Aby podłączyć panel AC'97 do karty HD Audio wykonaj poniższe kroki:
A.Podłącz Mic_IN (MIC) do MIC2_L.
B.Podłącz Audio_R (RIN) do OUT2_R oraz Audio_L (LIN) do OUT2_L.
C.Podłącz masę (GND) do masy (GND).
D.MIC_RET oraz OUT_RET są używane tylko w przypadku paneli HD Audio, nie musisz ich podłączać.
E.Wejdź do BIOS-u. Otwórz zakładkę Advanced Settings, a tam wybierz opcję Chipset Configuration. Przestaw Front Panel Control z [Auto] na [Enabled]. Dla Windows XP:
F.Włącz system Windows. Kliknij ikonę VIA ADeck w prawym dolnym rogu ekranu.
G.Kliknij "Mixer", wybierz "Front Microphones", zaznacz "Front Mic Boost" i zamknij program. Opcje te zostały pokazane na poniższym obrazku:
H.Jeżeli chcesz usłyszeć swój głos z mikrofonu podłączonego do przedniego panelu kliknij „Mixer", wybierz „Plac Back", zaznacz „Front Mix" i zamknij program, tak jak to pokazano na poniższym rysunku:
Dla Windows Vista/Windows7:
F.Wejdź do BIOS-u. Otwórz zakładkę Advanced Settings, a tam wybierz opcję Chipset Configuration. Przestaw Front Panel Control na [Enabled].
G.Włącz system Windows. Kliknij ikonę VIA ADeck w prawym dolnym rogu ekranu. Kliknij "Front Mic" i wybierz " Default Device".
H.Jeżeli chcesz usłyszeć swój głos z mikrofonu podłączonego do przedniego panelu, kliknij „Speaker Output", tak jak to pokazano na poniższym rysunku:
P (Q&A-70|245):
Podłączyłem do płyty głównej kartę graficzną PCIE z serii ATI 2xxx, 3xxx, 4xxx. Po zainstalowaniu wszystkich sterowników systemu Windows XP dla płyty głównej, w menadżerze urządzeń ciągle widoczne jest nieznane urządzenie dźwiękowe na magistrali „High definition audio". Co mogę zrobić?(1/12/2009)
O:Jest to zintegrowany w kartach graficznych z serii ATI 2xxx, 3xxx, 4xxxx kontroler dźwiękowy.
Proszę zainstalować sterowniki ATI HDMI audio.
http://ati.amd.com/support/drivers/xp/hdmiaudio-xp.html
P (Q&A-69|241):
I have a motherboard with Realtek HD Audio Codec. When I use Windows® XP SP3 or upgrade to Windows® XP SP3, the onboard audio doesn't work. What could I try?(11/27/2008)
O:Please try the Realtek latest audio driver.
The driver is available from this link: http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=14&PFid=24&Level=4&Conn=3&DownTypeID=3&GetDown=false
P (Q&A-66|232):
I install more than 2GB system memory on my system. When I run the "Sound Recorder" under Windows® XP, it always shows the following error message. What's wrong?
(7/31/2008)
O:This is the limitation of Windows® XP. Please refer to the Microsoft® Knowledge Base for details: http://support.microsoft.com/kb/284893
P (Q&A-65|230):
When I install Realtek HD Audio driver, I found the system shows below error message. What can I do?
(6/26/2008)
O:Please refer to below steps to reinstall Realtek HD Audio driver:
1.Enter into "Add or Remove Programs" and remove "Realtek High Definition Audio Driver"
2.Disable all "Microsoft® UAA Bus Driver for High Definition Audio" in Device Manager first
3.Then uninstall all "Microsoft® UAA Bus Driver for High Definition Audio" from the system.
4.Reboot system
5.Reinstall "Realtek HD Audio driver" from Motherboard Support CD.
If you still meet this problem, please reinstall fresh Windows® system.
P (Q&A-63|226):
My motherboard with Realtek ALC662 audio codec supports 5.1 channel HD Audio. But it has 3 audio connectors (Light blue, Lime and Pink) on the rear audio panel. How do I connect my 5.1 channel speakers to the rear audio panel?(3/24/2008)
O:Please refer to following steps to connect your 5.1 channel speakers:
1. Connect the "Rear Speaker" to Line In (Light blue) port
2. Connect the "Front Speaker" to Line Out (Lime) port
3. Connect the "Central / Subwoofer" to Microphone (Pink) port
4. Adjust the "Audio I/O" setting to "6CH Speaker" in REALTEK Audio Management. Please refer to the following picture:
P (Q&A-57|207):
After installing ATI HDMI audio driver for my ATI HD 2xxx series PCIE card, I found the onboard sound will not work. How do I fix the problem?(9/10/2007)
O:Please kindly refer to below steps to check your system setting.
1.Please double check the onboard sound is working properly in Device Manager.
(If not, please reinstall Realtek HD Audio driver from Support CD.)
2.Enter the Sound setting in the Control Panel.
3.If the Default device of the Sound playback is "ATI HD Audio rear output", please change it to "Realtek HD Audio output".
4.Press "OK" to save setting.
P (Q&A-54|200):
I have a motherboard with Realtek HD audio codec. After resume Windows® Vista™ from sleep or from hibernation, the high definition audio device may no longer work. How do I solve this?(4/25/2007)
O:This is caused by Microsoft. It can be solved by installing the Microsoft® Hot fix. Please refer to the Microsoft® Knowledge Base: http://support.microsoft.com/kb/929685/en-us
P (Q&A-53|198):
I have a motherboard with Realtek HD audio codec. After installing the Microsoft® Security Update 925902 and 928843, my system shows the following error message. How do I fix this?
(4/20/2007)
O:This is caused by Microsoft. It can be solved by installing the Microsoft® Hot fix. Please refer to the Microsoft® Knowledge Base: http://support.microsoft.com/kb/935448/
P (Q&A-52|196):
My onboard audio is Realtek HD audio. In the Windows® Vista™, I can't use Sound Recorder to record the audio. What should I do?(3/19/2007)
O:Please refer to below steps to set the audio device.
1.Install Realtek HD Audio driver from motherboard Support CD. Or download the Realtek HD audio driver from ASRock website.
https://www.asrock.com/support/Download.asp
2.Plug in your recording devices (Microphone or other devices) to the Line-in port (or Microphone port), and then the recording device will show up "Line In" (or "Microphone") icon. Please kindly refer to below image. (Control Panel > Sound > Recording)
*Before plug in the recording devices:
*After plug in the recording devices:
3.Reopen the Sound Recorder to record the audio.
P (Q&A-50|193):
I plugged a headphone in my ASRock motherboard with Realtek HD Audio, and set the "Audio I/O" from "2CH" to "Headphone" in Realtek Audio Manager (picture1).
But the Realtek Audio Manager always recognized my headphone as 2CH speaker after I restarted the operating system (picture2).
What should I do?(1/16/2007)
O:Please refer to the following steps to set up the Realtek Audio Manager correctly.
1.Please remove all audio I/O (Headphones, Speakers, Microphone...) from the motherboard.
2.Please go to Realtek Audio Manager and set the "Audio I/O" you want.
3.Click ok.
4.Please plug your audio I/O back.
5.Restart your system.
P (Q&A-50|192):
I would like to use the analog CD-in function in Windows® Vista™. But the "Analog" item of Playback and Rip can not be selected in Windows® Vista™. It was gray. Why? (Here is the screenshot.)
(1/16/2007)
O:Windows® Vista™ operating system does not support the analog CD-in. The output of CD/DVD-ROM playback will be digital only.
P (Q&A-42|172):
My onboard audio is AC'97 audio. The front panel audio connector cables of my case are different from the description of manual. How should I connect them? Please advice.(4/21/2006)
O:The wording on the front panel connector cables may be different by each chassis manufacturer. Please check the function of each cable. Otherwise it may damage the board if cables are connected to the wrong connectors. We found that if you connect the "GND" (Ground) or "USB VCC" (USB Power) connector pins to the "+5V" pin, it will damage the motherboard after booting up the system. So we recommend you must not install any connector on the +5V pin of the Front Panel Audio header. It will not affect the Audio function if you remove the connector from the +5V pin.
For this reason, we will remove the +5V pin from the Front Panel Audio header of our products in the future.
There are three examples for your reference, please refer to the following pictures.
P (Q&A-40|164):
If I use AC'97 front audio panel with, how do I connect to the High Definition Audio header on the motherboard and get front audio work?(2/17/2006)
O:If you use AC'97 audio panel, please install it to the front panel audio header as below:
A. Connect Mic_IN (MIC) to MIC2_L.
B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_RET and OUT_RET are for HD audio panel only. You don't need to connect them for AC'97 audio panel.
E. Enter BIOS Setup Utility. Enter Advanced Settings, and then select Chipset Configuration. Set the Front Panel Control option from [Auto] to [Enabled]. For Windows® XP
F. Enter Windows® system. Click the icon on the lower right hand taskbar to enter Realtek HD Audio Manager. Click "Audio I/O", select "Connector Settings", choose "Disable front panel jack detection", and save the change by clicking "OK".
For Windows® Vista™
F. Enter Windows® system, 1: Double click the icon on the lower right hand taskbar to enter Realtek HD Audio Manager. 2: Click the "Folder" icon at the top-right corner. 3. Check "Disable front panel jack detection". 4. Click "OK".
(Please refer to the following picture)
G. To activate the front mic: For Windows® XP:
Please select the Front Mic as default record device in No. 1.
If you want to hear your voice through Front Mic, please deselect "Mute" in No. 2 For Windows® Vista™:
1.Go to the "FrontMic" Tab in the Realtek Control panel.
Click "Set Default Device" to make the Front Mic as the default record device.
P (Q&A-40|166):
What's the requirement for High Definition Audio to work under Windows® XP 64bit?(2/17/2006)
O:For normal working of High Definition Audio under Windows® XP 64bit, there is a hotfix file provided by Microsoft. Please install the hotfix before installing the audio driver. Otherwise, the audio driver may not be installed successfully.
Please click the link to download the hotfix file:
http://support.microsoft.com/?kbid=901105
P (Q&A-7|34):
Can I use the microphone if I select 6 speakers in C-Media Audio Configuration?(5/9/2003)
O:If you select 6 speakers in C-Media Audio Configuration for 5.1 CH output, all three audio connectors (Line in, Line out and MIC) are defined as output connectors.
Microphone is an input device. So you are not able to use the microphone at this moment.
P (Q&A-7|33):
How do I select "Output Type" in C-Media 3D Audio Configuration?(5/9/2003)
O:Please select "Analog" for "Output Device" in C-Media 3D Audio Configuration.
P (Q&A-2|10):
If I want to use 4/6 speakers, how do I setup 4/6-Channel audio ?(11/26/2002)
O:STEP 1: 4 CH: Connect the front L/R channel to "Line Out", the rear L/R channel to "Line In".
6 CH: Connect the front L/R channel to "Line Out", the rear L/R channel to "Line In", and the Center/Subwoofer channel to "Mic In".
STEP 2:
After installation of C-Media Audio driver, you will find an icon "C-Media Audio configuration" on the taskbar.
STEP 3:
Click the icon, and the screen will show the current audio configuration.
Select "Output" to change your audio configuration. Select "Analog" for Output Type and choose "4 channels" / "6 channels" for your speaker configuration.