Utilizziamo i cookie per offrirti un'esperienza più personalizzata e fluida. Visitando questo sito web, acconsenti all’utilizzo dei cookie da parte nostra. Se preferisci non accettare i cookie o hai bisogno di maggiori informazioni, consulta la nostra Informativa sulla privacy.
Se siete pienamente consapevoli della categoria della vostra domanda, si può scegliere una delle categorie qui sotto per le domande più frequenti. Catalogo:
Risultati:
Q (488):
Ho una scheda madre TRX40. Alla voce Gestione dispositivi, c'è un dispositivo RTK Boot che mostra un punto esclamativo e non c'è uscita audio dalla porta audio. Cosa posso fare per risolverlo? (4/1/2020)
A:Se viene visualizzato un dispositivo RTK sotto Gestione dispositivi e la porta audio non può essere utilizzata, seguire i passaggi seguenti per rimuovere il dispositivo RTK e consentire all'audio di funzionare correttamente.
Passaggio 3. Cliccare con il pulsante destro del mouse sull'icona Start nel desktop e selezionare Gestione dispositivi per vedere se è visualizzato il RTK Boot nel sistema.
Passaggio 5. Fare doppio clic sull'icona UacCodecDownload_AllInOne_RsProxy_2.64.10
Passaggio 6. Premere il pulsante Start per avviare il flashing del firmware audio.
Passaggio 7. Una volta completato il processo di flash, lo strumento mostrerà Pass, il che significa che il firmware audio è stato aggiornato correttamente e non dovrebbe essere visualizzato il dispositivo RTK Boot alla voce Gestione dispositivi.
Q (487):
Quando registro tramite il microfono in Windows 10 1909, si verificano sibili nelle registrazioni.(1/1/2020)
A:Se si sente un sibilo dalle registrazioni, scegliere uno dei metodi seguenti per evitare il sibilo.
Metodo 1:
Passaggio 1.
Scaricare il driver audio ad alta definizione Realtek dal sito web di ASRock.
*Assicurarsi che il cavo LAN sia collegato durante l'installazione del driver audio Realtek.
Passaggio 2:
Aprire la "console audio Realtek”.
Passaggio 3.
Attivare l'opzione "La soppressione del rumore riduce i rumori stazionari ambientali” nell'APP della console audio Realtek.
Passaggio 4.
Una volta abilitata l'impostazione di cui sopra, la qualità della registrazione migliorerà.
Metodo 2:
Passaggio 1.
Fare riferimento al passaggio 1 e al passaggio 2 del metodo 1 per aprire la "console audio Realtek”.
Passaggio 2.
Regolare Incremento microfono su + 0db.
Passaggio 3.
Una volta che il valore di boost è stato regolato su + 0db, la qualità della registrazione migliorerà.
Q (468):
Come si installa l'applicazione Sound Blaster Connect in Windows 10 RS4 o versione successiva?(10/1/2018)
A:In generale, il sistema scaricherà automaticamente l'app in background dopo aver installato il driver Realtek Audio. Digita "Sound Blaster Connect" nella barra di ricerca di Win10 per accedere all'app.
Se l'app non viene visualizzata sul tuo sistema, segui i passaggi seguenti per installarla manualmente.
1. Assicurati che la tua scheda madre supporti Creative Sound e con il driver Realtek Audio installato.
* Visita la pagina delle specifiche della scheda madre su www.ASRock.com per i dettagli.
* Il driver Realtek Audio può essere installato/scaricato dal CD di supporto e dal sito Web ufficiale di ASRock.
2. Accedi a "Sound Blaster Connect” su Microsoft Store e clicca su "Scarica” per avviare il download. https://www.microsoft.com/en-sg/store/p/sound-blaster-connect/9n66rljrt8z2
3. Dopo l'installazione, cliccare su Avvia per avviare l'app.
Fare riferimento alla seguente tabella che supporta Creative SoundBlaster Cinema5.
Q (469):
Come installare l'app Realtek Audio Console in Windows 10 RS4 o versione successiva?(10/1/2018)
A:In generale, il sistema scaricherà automaticamente l'app in background dopo aver installato il driver Realtek Audio.
Digita "Realtek Audio Console” nella barra di ricerca di Win10 per accedere all'app.
* Collega il cavo LAN quando installi il driver Realtek Audio.
Se l'app non viene visualizzata sul tuo sistema, segui i passaggi seguenti per installarlo manualmente.
1. Vai a Gestione dispositivi per controllare se il driver audio Realtek sia stato installato.
* Il driver Realtek Audio può essere installato/scaricato dal CD di supporto e dal sito Web ufficiale ASRock: www.ASRock.com.
2. Fai riferimento al seguente link per accedere a "Realtek Audio Control” sul Microsoft Store e clicca su "Scarica” per avviare il download. https://www.microsoft.com/store/productId/9P2B8MCSVPLN
3. Dopo l'installazione, clicca su Avvia per avviare l'app.
Q (457):
Mi piacerebbe utilizzare l'auricolare Mixed Reality di Windows su HDMI integrata, cosa devo fare?(12/1/2017)
A:Segui i passaggi seguenti
1. Fai riferimento alle "Linee guida hardware PC per auricolare Mixed Reality di Microsoft” per verificare i requisiti hardware del sistema. https://support.microsoft.com/en-us/help/4039260/windows-10-mixed-reality-pc-hardware-guidelines
* Windows Mixed Reality richiede la scheda grafica Intel HD 620 integrata o maggiore GPU integrata compatibile con DX12.
2. Se è installata una scheda grafica esterna, abilita "IGPU Multi-Monitor” all'interno del BIOS.
Percorso del BIOS: Avanzate > Configurazione chipset > Multi-Monitor IGPU
BIOS Path: Advanced > Chipset Configuration > IGPU Multi-Monitor
3. Scarica la versione del driver VGA 15.60.01.4877 dal centro di download di Intel e installala sul tuo sistema.
Link per il download: https://downloadcenter.intel.com/product/128199/Graphics-for-8th-Generation-Intel-Processors
4. Installa il connettore USB 3.0 "Auricolare Windows Mixed Reality” alla porta USB 3.0 integrata.
5. Installa il connettore HDMI "Auricolare Windows Mixed Reality” alla porta HDMI integrata.
L'auricolare Mixed Reality di Windows dovrebbe ora funzionare.
Q (455):
Come posso riprodurre Dolby ATMOS tramite un ricevitore su Z270 Gaming-ITX/ac?(10/1/2017)
A:Fare riferimento ai seguenti requisiti, configurazioni e procedure di installazione.
[Requisiti]
Sistema operativo: Windows 10
Ricevitore / decoder: Onkyo TX-NR 747 o altro ricevitore che supporta HDCP 2.2
Lettore: unità Pioneer Ultra HD Blu-ray
Disco BD: la maggior parte dei dischi 3D / 4K BD
Software riproduzione: Power DVD 14 o versioni successive
[Installazione]
1. All'avvio del sistema, premere "F2” per accedere alla schermata di configurazione UEFI.
Vai su Avanzate > Configurazione CPU e abilita "Estensioni di protezione del software" nelle impostazioni del BIOS.
Premi "F10” per salvare e uscire dalla schermata di configurazione del BIOS.
2. Accedi al Sistema operativo. Installa tutti i driver per la scheda madre.
Installa il driver ME versione 11.6.0.1126 (supporta il Blu-ray Ultra HD). Scarica il driver dal seguente link: http://www.asrock.com/MB/Intel/Fatal1ty%20Z270%20Gaming-ITXac/index.asp#osW1064
3. Vai su Pannello di controllo> Hardware e suoni> Audio e seleziona "Uscita ricevitore”.
Q (396):
Il DTS Connect 5.1 Surround funziona con Windows 10? (8/1/2015)
A:A causa delle limitazioni del sistema operativo 10 di Microsoft Windows, DTS Connect 5.1 Surround non funziona sotto Windows 10.
Se vuoi utilizzare DTS Connect 5.1 Surround, scegli le versioni precedenti, ad esempio Windows 8.1/Windows 8/Windows 7.
Q (350):
Quando riproduco musica o film da Media Player sotto Win8 32/64 bit, Media Player si arresta in modo imprevisto e mostra un messaggio di errore ogni volta che si collega una cuffia al pannello anteriore dell'audio. Cosa posso fare? (9/1/2013)
A:Riapri Media Player e riproduci nuovamente il file per avere l'audio dal pannello audio anteriore.
Q (297):
Come impostare l'uscita del suono digitale (DTS5.1, Dolby5.1, DTS HD Master a Dolby True HD) via HDMI o SPDIF?(11/1/2011)
A:Requisiti:
OS: Windows7, Vista SP2 o successivi.
Ricevitore/decoder: amplificatore Onkyo TX-SR608, ad esempio:
Software di riproduzione: Power DVD10 v10.0.2025.52, ad esempio, o altro software di riproduzione.
Installazione:
1. Si prega di installare tutti i driver dal CD di supporto, dopo di ciò, si prega di controllare Gestione periferiche; non ci dovrebbe essere alcun "!" o "?" nella lista.
2. Entrate nel Pannello di controllo > Hardware e suoni > Suoni,
Se volete l'uscita tramite HDMI, selezionare [Uscita HDMI]
Se volete l'uscita tramite SPDI, selezionare [Uscita digitale]
*Differenti scheda madre/chipset possono mostrare diverse informazioni, la foto qui sopra è solo come riferimento.
3. Entrare nelle impostazioni audio dell'applicazione.
Prendiamo Power DVD 10 qui ad esempio: scegliete l'ambiente Speaker e modalità di uscita che si desidera.
4. Impostare il decoder/amplificatore per l'uscita audio digitale che si desidera.
5. Impostare il formato d'uscita corretta sul manuale dei vostri contenuti/fonte.
6. E potete poi riprodurre il contenuto/sorgente.
Q (263):
If I use AC'97 front audio panel with VIA® audio codec motherboard, how do I connect AC'97 front panel to HD Audio header on the motherboard?(2/10/2010)
A:If you use AC'97 front audio panel, please install it to the HD audio header as below:
A. Connect Mic_IN (MIC) to MIC2_L.
B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_RET and OUT_RET are for HD audio panel only. You don't need to connect them for AC'97 audio panel.
E. Enter BIOS Setup Utility. Enter Advanced Settings, and then select
Chipset Configuration. Set the Front Panel Control option from [Auto] to [Enabled]. For Windows® XP
F. Enter Windows® system. Click the icon on the lower right hand taskbar to enter VIA® ADeck. Click "Mixer", select "Front Microphones", choose "Front Mic Boost", and leave.
Like below picture:
H. If you want to hear your voice through Front Mic, Please click "Mixer", select "Play Back", choose "Front Mic", and leave.
Like below picture:
For Windows® Vista™ / Windows® 7
F. Enter BIOS "Chipset Settings" page, manual [Front Panel] to [Enable].
G. Enter Windows® system. Click the icon on the lower right hand taskbar to enter VIA® VDeck. Click "Front Mic", select "Default Device"
H. If you want to hear your voice through Front Mic, Please click "Speaker Output" icon.
Like below picture:
Q (245):
I install ATI 2xxx, 3xxx, 4xxx series PCIE VGA card on the motherboard. After installing all Windows® XP drivers from the motherboard, it still shows an unknown "audio device on the high definition audio bus." message under device manager. What could I try?(1/12/2009)
A:There is an integrated audio chip in the ATI 2xxx, 3xxx, 4xxxx series graphics cards.
Please install ATI HDMI audio driver.
http://ati.amd.com/support/drivers/xp/hdmiaudio-xp.html
Q (241):
I have a motherboard with Realtek HD Audio Codec. When I use Windows® XP SP3 or upgrade to Windows® XP SP3, the onboard audio doesn't work. What could I try?(11/27/2008)
A:Please try the Realtek latest audio driver.
The driver is available from this link: http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=14&PFid=24&Level=4&Conn=3&DownTypeID=3&GetDown=false
Q (232):
I install more than 2GB system memory on my system. When I run the "Sound Recorder" under Windows® XP, it always shows the following error message. What's wrong?
(7/31/2008)
A:This is the limitation of Windows® XP. Please refer to the Microsoft® Knowledge Base for details: http://support.microsoft.com/kb/284893
Q (230):
When I install Realtek HD Audio driver, I found the system shows below error message. What can I do?
(6/26/2008)
A:Please refer to below steps to reinstall Realtek HD Audio driver:
1.Enter into "Add or Remove Programs" and remove "Realtek High Definition Audio Driver"
2.Disable all "Microsoft® UAA Bus Driver for High Definition Audio" in Device Manager first
3.Then uninstall all "Microsoft® UAA Bus Driver for High Definition Audio" from the system.
4.Reboot system
5.Reinstall "Realtek HD Audio driver" from Motherboard Support CD.
If you still meet this problem, please reinstall fresh Windows® system.
Q (226):
My motherboard with Realtek ALC662 audio codec supports 5.1 channel HD Audio. But it has 3 audio connectors (Light blue, Lime and Pink) on the rear audio panel. How do I connect my 5.1 channel speakers to the rear audio panel?(3/24/2008)
A:Please refer to following steps to connect your 5.1 channel speakers:
1. Connect the "Rear Speaker" to Line In (Light blue) port
2. Connect the "Front Speaker" to Line Out (Lime) port
3. Connect the "Central / Subwoofer" to Microphone (Pink) port
4. Adjust the "Audio I/O" setting to "6CH Speaker" in REALTEK Audio Management. Please refer to the following picture:
Q (207):
After installing ATI HDMI audio driver for my ATI HD 2xxx series PCIE card, I found the onboard sound will not work. How do I fix the problem?(9/10/2007)
A:Please kindly refer to below steps to check your system setting.
1.Please double check the onboard sound is working properly in Device Manager.
(If not, please reinstall Realtek HD Audio driver from Support CD.)
2.Enter the Sound setting in the Control Panel.
3.If the Default device of the Sound playback is "ATI HD Audio rear output", please change it to "Realtek HD Audio output".
4.Press "OK" to save setting.
Q (200):
I have a motherboard with Realtek HD audio codec. After resume Windows® Vista™ from sleep or from hibernation, the high definition audio device may no longer work. How do I solve this?(4/25/2007)
A:This is caused by Microsoft. It can be solved by installing the Microsoft® Hot fix. Please refer to the Microsoft® Knowledge Base: http://support.microsoft.com/kb/929685/en-us
Q (198):
I have a motherboard with Realtek HD audio codec. After installing the Microsoft® Security Update 925902 and 928843, my system shows the following error message. How do I fix this?
(4/20/2007)
A:This is caused by Microsoft. It can be solved by installing the Microsoft® Hot fix. Please refer to the Microsoft® Knowledge Base: http://support.microsoft.com/kb/935448/
Q (196):
My onboard audio is Realtek HD audio. In the Windows® Vista™, I can't use Sound Recorder to record the audio. What should I do?(3/19/2007)
A:Please refer to below steps to set the audio device.
1.Install Realtek HD Audio driver from motherboard Support CD. Or download the Realtek HD audio driver from ASRock website.
https://www.asrock.com/support/Download.asp
2.Plug in your recording devices (Microphone or other devices) to the Line-in port (or Microphone port), and then the recording device will show up "Line In" (or "Microphone") icon. Please kindly refer to below image. (Control Panel > Sound > Recording)
*Before plug in the recording devices:
*After plug in the recording devices:
3.Reopen the Sound Recorder to record the audio.
Q (193):
I plugged a headphone in my ASRock motherboard with Realtek HD Audio, and set the "Audio I/O" from "2CH" to "Headphone" in Realtek Audio Manager (picture1).
But the Realtek Audio Manager always recognized my headphone as 2CH speaker after I restarted the operating system (picture2).
What should I do?(1/16/2007)
A:Please refer to the following steps to set up the Realtek Audio Manager correctly.
1.Please remove all audio I/O (Headphones, Speakers, Microphone...) from the motherboard.
2.Please go to Realtek Audio Manager and set the "Audio I/O" you want.
3.Click ok.
4.Please plug your audio I/O back.
5.Restart your system.
Q (192):
I would like to use the analog CD-in function in Windows® Vista™. But the "Analog" item of Playback and Rip can not be selected in Windows® Vista™. It was gray. Why? (Here is the screenshot.)
(1/16/2007)
A:Windows® Vista™ operating system does not support the analog CD-in. The output of CD/DVD-ROM playback will be digital only.
Q (172):
My onboard audio is AC'97 audio. The front panel audio connector cables of my case are different from the description of manual. How should I connect them? Please advice.(4/21/2006)
A:The wording on the front panel connector cables may be different by each chassis manufacturer. Please check the function of each cable. Otherwise it may damage the board if cables are connected to the wrong connectors. We found that if you connect the "GND" (Ground) or "USB VCC" (USB Power) connector pins to the "+5V" pin, it will damage the motherboard after booting up the system. So we recommend you must not install any connector on the +5V pin of the Front Panel Audio header. It will not affect the Audio function if you remove the connector from the +5V pin.
For this reason, we will remove the +5V pin from the Front Panel Audio header of our products in the future.
There are three examples for your reference, please refer to the following pictures.
Q (164):
If I use AC'97 front audio panel with, how do I connect to the High Definition Audio header on the motherboard and get front audio work?(2/17/2006)
A:If you use AC'97 audio panel, please install it to the front panel audio header as below:
A. Connect Mic_IN (MIC) to MIC2_L.
B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_RET and OUT_RET are for HD audio panel only. You don't need to connect them for AC'97 audio panel.
E. Enter BIOS Setup Utility. Enter Advanced Settings, and then select Chipset Configuration. Set the Front Panel Control option from [Auto] to [Enabled]. For Windows® XP
F. Enter Windows® system. Click the icon on the lower right hand taskbar to enter Realtek HD Audio Manager. Click "Audio I/O", select "Connector Settings", choose "Disable front panel jack detection", and save the change by clicking "OK".
For Windows® Vista™
F. Enter Windows® system, 1: Double click the icon on the lower right hand taskbar to enter Realtek HD Audio Manager. 2: Click the "Folder" icon at the top-right corner. 3. Check "Disable front panel jack detection". 4. Click "OK".
(Please refer to the following picture)
G. To activate the front mic: For Windows® XP:
Please select the Front Mic as default record device in No. 1.
If you want to hear your voice through Front Mic, please deselect "Mute" in No. 2 For Windows® Vista™:
1.Go to the "FrontMic" Tab in the Realtek Control panel.
Click "Set Default Device" to make the Front Mic as the default record device.
Q (166):
What's the requirement for High Definition Audio to work under Windows® XP 64bit?(2/17/2006)
A:For normal working of High Definition Audio under Windows® XP 64bit, there is a hotfix file provided by Microsoft. Please install the hotfix before installing the audio driver. Otherwise, the audio driver may not be installed successfully.
Please click the link to download the hotfix file:
http://support.microsoft.com/?kbid=901105
Q (34):
Can I use the microphone if I select 6 speakers in C-Media Audio Configuration?(5/9/2003)
A:If you select 6 speakers in C-Media Audio Configuration for 5.1 CH output, all three audio connectors (Line in, Line out and MIC) are defined as output connectors.
Microphone is an input device. So you are not able to use the microphone at this moment.
Q (33):
How do I select "Output Type" in C-Media 3D Audio Configuration?(5/9/2003)
A:Please select "Analog" for "Output Device" in C-Media 3D Audio Configuration.
Q (10):
If I want to use 4/6 speakers, how do I setup 4/6-Channel audio ?(11/26/2002)
A:STEP 1: 4 CH: Connect the front L/R channel to "Line Out", the rear L/R channel to "Line In".
6 CH: Connect the front L/R channel to "Line Out", the rear L/R channel to "Line In", and the Center/Subwoofer channel to "Mic In".
STEP 2:
After installation of C-Media Audio driver, you will find an icon "C-Media Audio configuration" on the taskbar.
STEP 3:
Click the icon, and the screen will show the current audio configuration.
Select "Output" to change your audio configuration. Select "Analog" for Output Type and choose "4 channels" / "6 channels" for your speaker configuration.